![]() Each of them requires a different alignment mode to be successfully scanned in the most efficient way.ħ.1 Scanning a small object using the Turntable Coded Targets alignmentĪ small object is placed on the turntable. In this section different objects are scanned. Selecting the alignment mode and scanning The brightness slider will be greyed out if HDR is enabled.ħ. Each single scan will take longer to capture. ![]() To scan an object with high contrasting texture, such as something white and black, use HDR. White or light grey indicates a proper brightness adjustment. The level should be set according to the following illustration: read means overexposed, black is underexposed. Use the slider to adjust the brightness sensitivity to its suitable value. The correct brightness setting will depend on the lighting in the environment and the texture of the object. When the proper distance between the object and the scanner surface has been set, the cameras brightness is to be adapted. The picture below shows, from left to right, the projected cross at a too close distance, optimal distance and too far distance. ![]() Adjust the distance until the cross is inside the central box. The picture below shows, from left to right, the projected cross at a too close distance, optimal distance and too far distance.Īnother way to make sure that the object is at the optimal distance is taking a look to the video feed from the software. If it is blurry, you might need to move your setup. In case you don't want to use a tape measure every time, you can check if the projected cross is clearly seen on the surface to be scanned. A summary can be found in the following table: The distance between the scanner and the area to be scanned depends on the scanner model. In this case, we are setting the EinScan Pro 2X at the optimal distance from the centre of the turntable, which is 400 mm. Once the Fixed Scan work has been created, we can adjust the distance between the scanner and the area to be scanned. In this example we will select a 'Non-texture Scan'. If you select 'Texture Scan' you will need to have the Color Pack connected. You will be asked whether you to scan with or without textures. Create a new project in the desired path and name it. Launch the EXScan Pro software and select the Fixed Scan mode. Introduce first the front of the scanner and afterwards push it gently downwards. Make sure the add-on port is kept facing up. Place the scanner horizontally on the scanner bracket. The next step is placing the scanner on the tripod. Note: 2X and 2X Plus scanner bracket is different to that from 2X2020 and HD, for the latter being wider. Mount the scanner's bracket on the spherical joint by placing the adaptor properly. Once the tripod is steady, take the mount adaptor and screw it under the scanner's bracket. Likewise secure them after setting the proper position.Īfterwards screw the spherical joint on top of the tripod. Make sure to unsecure the joint's fastenings before moving them. Launch the EXScan Pro software and calibrate the scanner.Įxtend the legs first and leave the centre column for later adjustment. The Industrial Pack turntable should be detected as 'USB Serial Converter' in the 'Universal Serial Bus controllers' group. In Windows Device Manager the scanner should be detected as 'SHINING-CAM', under the 'Cameras' group. Connect the Industrial Pack turntable to a USB port and power it. The latter depends on the scanner model:įor more detailed technical information about the different scan modes, please check the article: EXScan Pro Scan Modes.Ĭonnect the scanner to a USB3.0 port and power it. The Fixed Scan Mode achieves the highest accuracy and the highest accuracy. 7.3 Scanning a medium size object using Marker alignment.7.2 Scanning a medium size object using the Features alignment.7.1 Scanning a small object using the Turntable Coded Targets alignment.The Color Pack add-on can also be used in this mode and is compatible with the Industrial Pack. Perfect for scanning objects fitting the 150 mm diameter turntable. The add-on Industrial Pack is dedicated to this mode. Successive single scans are aligned automatically or manually, based on the common areas or markers to generate a complete scanned data set. The relative position between the scanner and the object can be changed to capture different areas of the object on separated single scans. In this mode the scanner and the object are fixed during a single scan. This article is based on software version 3.6.0.5įixed Scan Mode is designed for achieving high resolution and high accuracy scans for small (from 30 x 30 x 30 mm) to medium size objects.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |